Table of Contents
How to Fix Your Lennox Furnace with These 6 Simple Steps
Your furnace can make or break your day in the cold months of winter. If it fails or breaks down at home, you’ll be faced with the prospect of freezing all night long. Aside from that, leaving your house unheated will strain your electricity bill and force you to spend even more money than what you already have. Having a busted furnace is something that no one wants to deal with, but it’s part of life and something we all have to accommodate sooner or later. They are relatively common household appliances that often give out problems when they don’t work as intended. If you own a Lennox furnace and can’t seem to get it working again, don’t worry! The following article contains everything you need to know about fixing your Lennox furnace and getting back on track in no time!
Check the Furnace’s Filters
Filters are essential components of every furnace. They keep your furnace clean and may even extend its lifespan. If your furnace has been running non-stop for a while and the filters are dirty, they can cause your furnace to overheat and shut down. When this happens, the furnace will stop running, and you’ll notice that it’ll be very hard to get it going again. When cleaning the filters, make sure that you do it so that they are completely dry before putting them back into the furnace. If they are damp, they can cause your furnace to break down once again. To clean your filters and make sure they’re ready to go, use gloves and a vacuum cleaner to remove all the dirt and debris accumulated in them. When you’ve finished, place them back into their correct positions and ensure they are properly secured. They should be placed toward the back and above the motor.
Check Your Thermostat
The thermostat is the heart of your furnace. It’s what makes the entire system work. It will be impossible for your furnace to start if it’s broken. You should check it to see if it’s not very accurate. If it is, you’ll need to replace it. If your thermostat is digital and has a wireless connection, check for any issues with the wiring or the batteries. If you don’t see any issues, you can reset it and see what happens. If your thermostat is not digital, or you see issues with it, you’ll need to replace it with a new one.
The Furnace’s Blower
The blower is the furnace part that blows air through the system and heats the house. If it has been used a lot and it’s broken, you’ll need to replace it. To do that, you should shut off the power to the furnace and remove the covering. You can then access the blower and remove it. To put in the new blower, do the opposite and ensure that you put it in the right way. When replacing the blower, make sure that you check the motor’s RPM and ensure it’s within the proper range. You can remove the blower and then take the motor out if it’s not. Then, use a screwdriver to adjust the speed to make it higher or lower. You can then put it back together and put the blower back.
The Burners and Gas Valve
If your furnace has been on for a long time and you see that the burners aren’t lighting up, it might mean that the gas valve is broken. If that’s the case, you’ll need to replace it. To do that, shut off the power to the furnace and remove the covering. You can then access the gas valve and remove it. When you’ve removed the gas valve, check the connections. If they are loose, tighten them. To replace the gas valve, you need to be careful. Make sure that you buy the right model and replace it with the same kind. If you don’t, you can make the problem much worse. Make sure that you install the new valve in the right way.
The Furnace’s Electronic Control
The furnace’s electronic control is the part that makes the furnace run. If it’s broken and can’t get it working, you’ll have to replace it. Before you do, however, make sure that you turn off the power to the furnace. When replacing the furnace’s electronic control, you need to make sure that you buy the right model. If you don’t, you can cause the problem to get even worse. Once you’ve bought the new one and opened the control box, remove the old one and put the new one in its place.
Conclusion
When it comes to furnace repair, you don’t want to be in a rush to get it done. Instead, you want to take your time and ensure that you’re doing the job right. If you rush, you’re more likely to make a mistake that will cause the problem to get even worse. With the tips and tricks that we’ve provided in this article, you’ll be able to fix your furnace and get back to your normal routine in no time!
