The Top 5 Reasons Why You’re Getting a Water Furnace Geothermal Error Code

When you’re installing a geothermal heating and cooling system, it can be easy to overlook some details. After all, many different moving parts need to be in place for the system to function properly. And the plumbing is certainly one of those places where you might overlook some details. It’s important to keep in mind that any home heating and cooling system is going to have its ups and downs. Sometimes things will happen beyond your control and you might get an error code on your water furnace geothermal heat pump. But don’t worry! There are some very common reasons why this might happen, so we’ve listed them here for you.

Geothermal Error Code 12

The first error code you might see when you have issues with your water furnace geothermal heat pump is Error Code 12. This error is related to the refrigerant process in the system. Your system uses refrigerant to move heat through the pipes. When there are issues with the level of refrigerant in your system, you might see Error Code 12. There are a few reasons why your system’s refrigerant levels may be off. The most common reason for a low refrigerant level is when there is a leak in the system. There may be a leak in your pipes or in the parts of the system that are attached to the pipes. If there’s a leak in your system, you will need to find and fix it. Once you’ve done that, you can start the process to get your system back up and running again.

Geothermal Error Code 14

Error Code 14 is related to your pressure switch inside your water furnace geothermal heat pump. The pressure switch makes sure that your system doesn’t overheat and shuts off automatically. If the pressure switch doesn’t read right, you might see Error Code 14. The most common reason why your pressure switch may have issues is if something is blocking the path of the system. If your pressure switch isn’t getting the right readings, it may be because there is a blockage in the path of the water or air. If there is an issue with the system, you will need to find and remove the blockage. Then, you can reset your pressure switch and try the system again.

Geothermal Error Code 21

Error Code 21 is another common error you might get when you have issues with your water furnace geothermal heat pump. Error Code 21 is related to a low flow rate in your system. This means that there is not enough water flowing through your pipes to heat and cool your home. There are a few reasons why your flow rate might be off. The most common reason is that there is a blockage in your system. If there is something in your pipes, it won’t let enough water through to heat and cool your home. Once you’ve found and removed the blockage, you can try your system again.

Geothermal Error Code 32

Error Code 32 is related to your water temperature. It means that your water temperature is too low. This is normally caused by an issue with the outdoor temperature. If your outdoor temperature is too low, it won’t be able to heat your water to the right temperature. There are a few reasons why your outdoor temperature might be too low. The most common reason is that you have a power outage. If you have no electricity, you won’t have the power to run your water furnace geothermal heat pump. There are a few ways that you can get your outdoor temperature back up. You can open your windows to let some heat inside. You can also use an emergency heat source, like a fireplace or portable heater, to warm up your water indoors.

Geothermal Error Code 34

Error Code 34 is another error code that is related to your water temperature. It means that your water temperature is too high. This is normally caused by an issue with the indoor temperature. If your indoor temperature is too hot, it won’t be able to cool your water to the right temperature. There are a few reasons why your indoor temperature might be too hot. You might have a few too many appliances running in your home. Or, you may have a clogged vent that is preventing your system from cooling your home correctly. If your indoor temperature is too hot, you can turn off some of your appliances. You can also make sure that you have enough ventilation to cool down your home.

Conclusion

One of the biggest reasons why someone might get a water furnace geothermal error code is because they didn’t fully understand the installation process. When you’re installing a new heating and cooling system, it’s important to follow the instructions and make sure that everything is installed correctly. Once you have a better understanding of what each part of the system does, it will be easier to troubleshoot any problems that might come up. And if you do run into issues, it’s important to remember that they aren’t permanent!